Lab Equipments

Product Details:

The Laboratory jaw Crusher is designed for fast crushing of Aggregates, Ores, Milnerals, Coal, Coke, Chemicals and other similar materials. It is compact and of rugged construction for general Laboratory of small pilot plant operations. Two jaws of manganese steel are provided in this Laboratory jaw Crusher. The moveable jaw produces tow blows for every revolution, thus reducing over sizing to a minimum. A combination of forward and downward strokes with a rocking action exerts pressure on the coarser material, yet permits the finished material to pass through the jaws. A hopper is provided at the top for feeding material The smooth jaws ensure a uniform product and easy cleaning is possible.

Model overview:

• SL234.1 Jew Crusher (Small) SL234.2 Jaw Crusher (Medium) SL234.3 Jaw Crusher (Large)
• ASI-184 Jaws Size (mm) 100 x 150 150 x 200 200 x 300
• ASI-185 Size of Feed material (mm. Approx) 50 25-75 50-100
• ASI-186 Yield (kgs./Hr) Approx 80 250 400
• ASI-187 Size of Finished Product (mm) 6 to 18 (adjustable) 12 to 25 (adjustable) 12 to 30 (adjustable)
• ASI-188 Power Requirement 440 V, 3Ph, 50 Hz. 440 V, 3Ph, 50 Hz. 440 V, 3Ph, 50 Hz.

Additional Information:

• Item Code: ASI-234

Product Details:

We are a leading manufacturer, supplier and trader of superior quality Ductility Testing Apparatus. The apparatus consists of a water bath with a thermostatic heater and a circulating pump to maintain uniform water temperature. These products are manufactured under the close supervision of our experienced professionals using high quality material.

Features:

• Tough construction
• Minimal maintenance cost
• Easy to use

Other Details:

• In flexible pavement construction, bitumen binders are used. It is important that bituminous material forms ductile thin film around the aggregates, which serves as a binder
• The binder material not of sufficient ductility renders previous pavement surface and leads to development of cracks
• Therefore it is important to carry out the ductility tests on bituminous material. Ductility is defined as distance in cms

• The apparatus consists of a Water bath with a thermostatic heater, and a circulating pump to maintain uniform water temperature.
• One half of the briquette moulds in fixed on a fixed plate in the water bath, the other half of the briquette mould is fixed to a carrier which slides over a rotating threaded shaft with a clutch.
• The motor and gears to rotate the shaft are housed in a cabinet fixed above the other and of the bath.
• Control switches for motor, stirrer, heater and indicator lamps are fixed at a convenient place on the water bath.

Additional Information:

• Item Code: ASI-105

Product Details:

Los Angles Abrasion Testing Machine 

Used for testing crushed rock, crushed slag, crushed and uncrushed gravel for resistance to abrasion.

Components: The machine consists of a hollow cylinder mounted horizontally on a study frame on ball bearings. There is an opening which can be closed with a dust tight cover to facilitate charging and discharging the drum with the material under test. A detachable shelf which extends throughout the inside length of the drum which catches the abrasive charge and does not allow it to fall on the cover. A revolution counter is fitted to the frame. A tray is supplied for collection of the material at the end of the test. 

As Per IS: 2386 (Part IV) ASTM: C 131, AASHP T 96

Additional Information:

• Item Code: ASI-315

Product Details:

We are one of the accredited manufacturers, suppliers and traders of a premium range of Marshall Stability Test Apparatus. Offered range is used in designing and evaluating bituminous paving mixes. These products are used to determine optimum binder content for the type of aggregate mix and traffic intensity. Besides, we assure timely delivery of consignments at clients’ destinations.

Features:

• Compact design
• Easy usage
• Fine finish

Other Details:

• Generally the test is applicable to hot mix designs using bitumen and aggregates upto a maximum size of 25mm.
• In this method, the resistance to plastic deformation of cylindrical specimen of bituminous mixture is measured when the same is loaded at periphery at 5cm per min.
• This test procedure is used in designing and evaluating bituminous paving mixes.
• The test procedure is extensively used in routine test programmers for paving jobs.
• There are two major features of the Marshall method of designing mixes namely. a) densityvoids analysis, b) Stability-flow tests.
• The Marshall stability of mix is defined as a maximum load carried by a 0 compacted specimen.

Additional Information:

• Item Code: ASI-110

Product Details:

We are offering a wide range of Aggregate Impact Tester which is used for determining the aggregate impact value.


As Per IS: 2386 (Part-IV) 9377

Additional Information:

• Item Code: ASI-309

Product Details:

Water Bath

Rectangular water bath, double walled construction, inside reservoir of stainless steel, outer body mild steel with insulation in between, supplied with a lid having one hole of 12.5cm dia. and four holes of 7.5cm dia. Concentric Rings with lids are provided on holes. The top plate and concentric rings are of S.S. Temperature 0 0 0 range 7 C above ambient to 95 C 1 C by capillary thermostat.These water baths are useful for Laboratory work.

Additional Information:

• Item Code: ASI-1113

Product Details:

Universal Water Bath

Single walled body made out of full stainless steel, polished sheet, temperature 7 C above ambient to 0 boiling point of water 1 C by thermostatic arrangement. These baths are useful for heating Marshal specimen. A false button of S.S having holes is provided over the heating element.

Available in the following sizes and accessories : (a) 12”L x 9” W x 7”H having rating of 750 W., (B) 18” L x 12”W x 7”H having rating 1500W. 1. Pyramid lid for size (a) 12” L x 9” W x 7” H, (b) 18” L x 12”W x 7”H. Supplied without the thermometer, suitable for 230volts. A.C. single phase.

Additional Information:

• Item Code: ASI-1114

Product Details:

Viscometric Water Bath

Rectangular water bath, double walled construction, inside the reservoir of stainless steel, outer body mild steel with insulation in between, supplied with a lid having one hole of 12.5cm dia. and four holes of 7.5cm dia. provided with a glass window on the side.

Accessories: Viscometer holder for 4 nos. Viscometers and viscometer tray.

Note: Water baths having higher capacities can be supplied prices on request.

Additional Information:

• Item Code: ASI-1117

Product Details:

Aggregate Crushing Value Apparatusis used for measuring of resistance of aggregate to crushing.

As Per IS: 9376, 2386 (Part-IV)

Note:- On special request Aggregate Crushing Value apparatus having 75mm dia. or 300mm dia. cylinder size can be supplied.

Additional Information:

• Item Code: ASI-308

Product Details:

Bottom Heating Thermostatic Hot Air Ovens

Offered provides for stable test space in physics and chemistry testing. Some of its features include

• Precision temperature controller
• Fine powder coating treatment
• Inner SUS#304 stainless steel finish
• Using high temperature resistant long shaft motor
• Over temperature protection
• Heating system comprising PID+S.S.R
• PID microcomputer control and automatic constant temperature
• Power failure alarm indication

Sizes 

Additional Information:

• Item Code: ASI-1118

Product Details:

We are offering a wide range of Deval Attrition Tester which is used for the determination of resistance of aggregates to wear by abrasion.

Components: It consists of two hollow cylinders closed at one end and provided with tight fitting covers at the either end through a reduction gear operated by a motor and is provided with a revolution counter. Complete with abrasive charges consisting of 12 Nos. 

As Per IS: 2386 (Part-IV) ASTM D 2, D 289.

Additional Information:

• Item Code: ASI-312

Product Details:

Dorry Abrasion Testing Machine

For testing aggregates for resistance to abrasion.

Components: It consists of a disc rotating about a shaft connected to a reeducation gear box coupied to a motor. Under the rotating disc is a tray with an outlet to facilitate the removal of sand. Two conical hoppers are mounted on a bracket fixed to the circular tray. An arrangement is made for start and stop the flow of sand. Two holes are provided for mounting two specimens simultaneously. Two containers with weights are supplied to keep the specimens pressed against the rotating disc.

Additional Information:

• Item Code: ASI-313

Product Details:

Flow Cup Viscometers are useful for determining the flow time of paints varnishes, lacquers and other viscous products. They consist of a metallic container with specified dimensions and volume, incorporating and orifice. The sample flows through the orifice and the variations in running time indicate the variations in viscosity of the product, due to blending and dilution.

Additional Information:

• Item Code: ASI-1021